Intrinsically Safe Detectors

Conventional (SUO601)

The Tyco Manual Call Point (MCP) is a surface mounting call point with a plastic coated glass element to ensure reliable, safe operation. The Tyco MCP’s are available coloured Red or White. Note that for Red coloured devices, it is necessary to order both the MCP and the Wall Box.

The call point is operated by snapping the glass element by pressing on its centre – a hammer, or other impact device, is not required. The snapped glass element releases the MCP’s micro switch, which signals an alarm to the fire panel.

Technical Data Sheet
Brochure
SSL Approval

SU0600 15V Manual Call Point

The SU0600 15V Manual Call Point (MCP) clamps the line voltage to 15 volts when actuated. When used on the same circuit as collective fire detectors, it complies with AS1670.1 by not extinguishing the LED indicator of an already activated fire detector. This MCP has a plastic coated frangible element to ensure safe and reliable operation, producing no dangerous glass shards. The MCP is operated by simply pressing on the centre of the frangible element until it snaps. This releases the MCP’s micro switch, which signals an alarm at the FIP and illuminates the integral LED indicator. The unit features IN and OUT terminals, which are requirements of AS1670.1 and is compatible with the MX4428 ADR-M, F3200 (band 3 Instant Alarm) and F08 version 3.

Specifications

Operating Voltage 18 to 28Vdc
Quiescent Current 5μA max. @ 24Vdc
Alarm Current* 30mA max.
Alarm Current 1mA max @ 8Vdc
Alarm Voltage 14 to 16Vdc
Reverse Polarity Current 100mA max.
Reverse Polarity Voltage 0 to 1Vdc
Ambient Temp -10 to +70°C Indoor only
Relative Humidity 10% to 95% (non cond.)
CSIRO ActivFire Listed afp-1385

Part Numbers

SU0600 15V MCP (excl. backbox)
SU0632 Red Backbox
SU0615 Transparent Hinged Cover
515.001.025 Spare Glass (pk 5)

*Max. current must be externally limited

SU0631 Manual Call Point

The SU0631 Manual Call Point is supplied with one normally open and one normally closed contact. Selecting either the “Normally Open” or “Normally Closed” contact is easily achieved by simply connecting the terminal block to the required connection in the back of the MCP. Single pole changeover switching can be achieved with the use of two terminal blocks. The Call Point and Backbox are ordered separately. The call point is operated when the frangible glass element is snapped, releasing the MCP’s micro switch, which signals an alarm to the fire panel.

Specifications

Max. Operating Voltage 30Vdc
Max. Switch Current 2A
Cable Termination 0.5 to 2.5 mm2
Relative Humidity 0 to 95% (non/cond)
Ambient Temperature -10°C to +55°C
Weight 110g (flush)
Ingress Protection IP24D

Part Numbers

SU0631 Manual Call Point
SU0632 Red Backbox
SU0615 Transparent Hinged Cover
SC070 Spare Test Keys (pkt10)
515.001.025 Spare Glass (pkt 5)
See page 12 for MCP accessories

4099-9032 Manual Call Point

The 4099-9032 addressable Manual Call Point (MCP) provides a means to manually initiate a fire alarm condition to the 4100U c.i.e. via the IDNet channel. The IDNet channel provides the communication link and power between the call point and 4100U. Activation of the MCP requires the frangible element to be broken, which causes contacts on a microswitch to close, initiating an alarm condition. Call Point reset requires the fitting of a replacement frangible element. The MCP features an integral red LED status indicator. The Simplex 4099-9032NL MCP is connected to Simplex c.i.e. via MAPNET II and does not have a status indicator.

Specifications

Comms Power1 24 to 40Vdc w/data
Dimensions (HWD) 86x87x35mm
Ambient Temperature -9°C to +70°C
Relative Humidity 10% to 95% (n/c)
CSIRO ActivFire listed afp-1691

Part Numbers

4099-9032 IDNet & red LED
4099-9032N MAPNET II, no LED
515.001.025 Spare Glass (pk 5)
SR3T-P Backbox c/w Terminals

1. MAPNET II or IDNet communications with data

SU0608 Evacuation Manual Call Point

The SU0608 MCP is surface mounting, with a plastic coated glass element to ensure reliable, safe operation. It is coloured white (for EWIS applications) to be used where a fire alarm system does not exist. The call point is operated when the glass element is snapped, releasing the MCP’s micro switch, which signals an alarm to the EWIS panel. The element is snapped by pressing on its centre – a hammer, or other impact device, is not required.

Specifications

Max Current Resistive 8A @ 30Vdc
Inductive 3A @ 30Vdc
Contact Resistance 100mOhm. (max)
Legend Emergency Alarm
Ambient Temp -30 to +70°C
Relative Humidity 95%(non cond.)

Part Numbers

SU0608 White MCP & Backbox
515.001.025 Spare Glass (pk 5)

SU0611 Waterproof Callpoint

This surface mounting Manual Call Point has a plastic coated frangible element to ensure safe and reliable operation, producing no dangerous glass shards. The SU0611 is an IP67 rated MCP wih a single pole changeover switch configuration. SU0611 is operated by simply pressing on the centre of the frangible element until it snaps. A hammer, or other impact device, is not required. The snapped frangible element releases a microswitch, which signals an alarm at the CIE. It carries LPCB approval.

Specifications

Operating Voltage 230VAC (max.)
Operating Current 3A @ 230VAC (max.)
Dimensions (HWD) 125x125x80 mm
Ingress Protection IP67
Not CSIRO ActivFire listed by Tyco

Part Numbers

SU0611 MCP
515.001.025 Spare Glass (pk 5)
SU0622 Gasket Pack of 5

SU0612 Rainproof Callpoint

This surface mounting Manual Call Point has a plastic coated frangible element to ensure safe and reliable operation, producing no dangerous glass shards. The callpoint is operated by simply pressing on the centre of the frangible element until it snaps. A hammer, or other impact device, is not required. The snapped frangible element releases a microswitch, which signals an alarm at the CIE. The SU0612 provides IP55 protection for the terminal enclosure and IP55 for the switch. Ex rated devices are available. Contact TSP.

Specifications

Operating Voltage 230VAC (max.)
Operating Current 3A @ 230VAC (max.)
Dimensions (HWD) 123x123x80 mm
Ingress Protection IP55
Not CSIRO ActivFire listed by Tyco

Part Numbers

SU0612 MCP
515.001.025 Spare Glass (pk 5)
SU0623 Gasket Pack of 5

Weather STOPPER

The callpoint STOPPER provides protection from malicious or accidental activation of manual callpoints. Available for flush or surface mounted callpoints the ‘STOPPER’ is also available with optional high pitch sounder which is activated when the lid is lifted. An optional ‘Break-Seal’ fitting kit allows ‘Break-Seals’ to be used to provide extra protection.

Specifications

STI6535 STI3150
Dims (HWD) 210x137x57.5 254x178x86
Call Point Size 100x100x57.5 160x160x120
Ingress Protection Weatherproof

Part Numbers

515.001.033 IP036 Break Seal Kit
515.001.032 STI6533 Surface fit Weather STOPPER with sounder
515.001.035 STI3150 Weather Stopper II
515.001.036 STI6535 Weather Stopper

Weather STOPPER II
	The Weather STOPPER II extends the life of weather exposed callpoints, by offering protection against harsh conditions and environments, eg, oil rigs and ship decks. While offering environmental protection the Weather STOPPER II are constructed from polycarbonate which will also guard against tampering or accidental operation of devices.

Manual Call Point Ancillaries

Part Numbers

SU0605 Spare glasses, WORMALD white English text on clear background (Pack 10)
515.001.025 Spare glasses, clear text on white
background, no logo (Pack 5)